![Rick Van Dyke](/img/default-banner.jpg)
- 5
- 72 880
Rick Van Dyke
Приєднався 22 лис 2012
Boat Trailer Brake Line Warning MUST SEE!
Had I known my brake lines had gotten this bad I’d have replaced them a long time ago. Learn from my experience before something terrible happens
Переглядів: 1 063
Відео
Custom fish fillet and rigging table
Переглядів 502 роки тому
I couldn’t find what I wanted in a table so I decided to make my own. I go through the hows and why this design worked for me.
Replace power trim switch on Mercury 3000 Classic throttle assy
Переглядів 64 тис.3 роки тому
Replace power trim switch on Mercury 3000 Classic throttle assy
Boat launch fail, fail, fail, fail, fail….
Переглядів 293 роки тому
Boat launch fail, fail, fail, fail, fail….
Throttle advancement button broke. you said they were $3 or $4 all day. Any suggestions on where to find one?
Thanx for the video. I still have a problem and at my wits end. I’ve replaced the trim switch and both solenoids on the pump. Trailer switch works as does the switch at the transom. The trim switch on the throttle works down but not up. Where do I look next?
Thank you
Is "advanced throttle control" the same as "throttle only" mode?
Great explanation!
Can you tell me where the purple wire connects to in that arm.
Thanks for the video saved my boat from me burning it on the trailer😂
You don't have to cut the wires. There is a plug for the switch assembly harness.
.
OK - first of all... thanks for the video. I learned SOME things that were really helpful. Now to the critique. I found it to be impossible to get that "throttle only" button out without breaking it. Impossible. On yours there was only one barbed end piece instead of the four it was made with. That's why you were able to get yours out. With the full set of four barbs, it will not come out. I broke the pushbutton end of it clean off. True that there are inexpensive replacements available, but still - isn't there a way to open this whole assembly up without breaking it????
I broke mine off too. Do you know where to get a replacement?
@@iceMP14 I do, but UA-cam is apparently preventing me from sharing that knowledge with you. Hmm.
@@jschwar5I too am interested in getting this replacement piece! Please share where to search
822212T BUTTON-THRTL@5 (Mercury Marine)
thankyou
Exactly the video I needed. Thank you 👍🏻
Thanks Rick, very helpful, I appreciate your time n effort to show us this. Cheers for that.
great video
Wish i had watched thisbefore i started. Would have sa ed me ti.e and treasure...
Best video for this job! Thanks!!
so you have a video on how you put it back together. Mine fell off while I was coming back in to dock. scared the crap out of me. So now its dangling. Looks like my teeth are stripped. Trying to get a replacement but wanted to see a video of someone putting it back together again.
Not sure I can help you without seeing your setup. Watch it a couple times and it will make sense, not a lot of moving parts. Look for a video on cable replacement and it my show a little more detail. I’m just a DIY guy and not a mechanic, o wish you well on your repair. Remember a day on the water is a day better than anything else
Hi, quick question, what's the difference between inboard vs outboard shifter, can I buy an outboard shifter for an inboard engine? Thanks for your help!
I’m just a DIY guy and not a mechanic. But I do know that not all shift cables are the same, they are specific to the manufacturer of your motor. You will need to match that manufacturer. A quick google search should get you on the right track. Good luck with your project
My quick silver has only 3 wires?
Sorry, but I’m not a boat repairman. I’m just a DIY weekend warrior. When I can’t find a video on YT for something I make my own. I really appreciate when someone else does. What you see is what I know. The replacement switch wires are properly color coated. Just connect the ones you do have and leave the last one free. I just pet a little electrical tape on the end so no possibility of it shorting something. Good luck on your project
Where can I lookup replacement trim switch for my Mercruiser Alpha One zen 2 Quicksilver remote control?
Hey rick I have the same old 3000 unit that you had and want to update it to a newer smoother one whats the one you used after the fact and how do you like it? was it a pain doing the wiring change?
awesome work Rick
Thanks!
Thanks much. Didn't want to start ripping the thing apart before learning how it SHOULD come apart.
These parts are on short supply. So I’ll probably sell mine after upgrading.
Thank you. I did not have to break plastic parts to disassemble.
Good man. Saved me at least 2 hours.
Bro can you tell me wish of those wires is the one that goes to the trim gauge?
The blue one, I recommend doing a Google search for Mercruiser trim switch wiring diagram to familiarize yourself with the whole system. Good luck with your repairs
@@mobettastufffosur I have been looking on google but there’s nothing about it it’s really hard to find it thanks anyway
Your time and explanation is VERY much appreciated, sir! Thank you
This three minutes saved me I was getting nowhere as I haven't seen these in 10+ years until today, thank you
Thanks a million for this video.....the manual is worthless.
I removed the front then cover then the sliding top piece. Your instructions helped thank you
Thanks. Looked at and headed straight to youtube to figure out how to remove it.
Thanks for the video spent an hour trying to figure this out without breaking it, with your video had it off in five minutes. :)
Thanks for the instructions, I have spent an hour or more trying not to break the unit, I can now confidently remove it.
So what's the upgrade from p66? I just upgraded to the p66.